Community Stories

Helium crown came off

Mr.Wolf
Posts
65
Likes
6
Hello!

I've got a Seamaster 2250.50 and the helium crown fell off when i opened the valve a while ago. I would like to try to re-fit it myself with loctite. I understand that only a very small amount is needed. But how do i keep the loctite from getting on the spring and other parts where its not sopposed to be?
 
p4ul
Posts
1,687
Likes
3,979
Mr.Wolf Mr.Wolf
Hello!

I've got a Seamaster 2250.50 and the helium crown fell off when i opened the valve a while ago. I would like to try to re-fit it myself with loctite. I understand that only a very small amount is needed. But how do i keep the loctite from getting on the spring and other parts where its not sopposed to be?

DON’T!
Take it to a qualified watch repairer who will do the job properly, this will maintain water resistance.
 
Mr.Wolf
Posts
65
Likes
6
Of course iv'e considered that, but since my watchmaker shut down i haven't found another one who can fix it themselves. They just want to send it to Omega witch seems like big cost for a easy fix.

The actual valve don't seem to be damaged, would it be ok, to have it screwed down until the next service in a few years? I'm not going to dive ore swim wit it. I see that i cant be totally sure the valve isn't damaged and will be careful with it around water for now.
 
p4ul
Posts
1,687
Likes
3,979
If you give your city/country someone on here will give you a suitable recommendation I would think.

Depending on the age of your watch you may have warranty left or need a service so omega may not be as scary as you think, do you have a boutique or omega dealer near you? Go talk to them?
 
Mr.Wolf
Posts
65
Likes
6
Ill hear around for some who could do it! Got two dealers around and will ask at a local forum. The watch is from 2010 so no warranty left unfortunately no warranty left. Thanks for your commitment!
 
Archer
Posts
28,136
Likes
71,960
To install the valve cap, the case has to be opened and the movement removed. This is a job for a watchmaker...
 
Flintlock
Posts
164
Likes
78
I'll also chime in for an Omega qualified watchmaker. Is it perchance due for service anyway? That would maybe just be part of the service.
 
BlackTalon
Posts
5,444
Likes
9,323
I'm curious if any of the other divers who were in the decompression chamber with you had helium escape valves on their watches (or even wore regular wrist watches since I guess you all wear diving computers). My Sinn UX -- which is rated for a lot deeper water than the Seamasters -- does not have one, but it is filled with some magic oil.

I was under the impression you are not supposed to loosen the escape valve very much for it to be effective -- definitely not enough to fully unscrew anything. Did something possibly break off?. The deepest diving I have done is about 20-25 feet, and all at resorts (so literally train in the pool for a day and go dive for 20 or some minutes out at a reef) so I have never needed to worry about decompression and it's potential effect on my watches.
 
Archer
Posts
28,136
Likes
71,960
BlackTalon BlackTalon
I'm curious if any of the other divers who were in the decompression chamber with you had helium escape valves on their watches (or even wore regular wrist watches since I guess you all wear diving computers). My Sinn UX -- which is rated for a lot deeper water than the Seamasters -- does not have one, but it is filled with some magic oil.

Sinn typically epoxies the crystals into their watches, so the pressure needed to blow the crystal out (the main concern) is much higher.

BlackTalon BlackTalon
I was under the impression you are not supposed to loosen the escape valve very much for it to be effective -- definitely not enough to fully unscrew anything. Did something possibly break off?. The deepest diving I have done is about 20-25 feet, and all at resorts (so literally train in the pool for a day and go dive for 20 or some minutes out at a reef) so I have never needed to worry about decompression and it's potential effect on my watches.

The HEV cap screws onto a case tubes much like a screw down crown would. It is unscrewed as far as it can go, and then what holds it in place is the screw that goes into the center of the cap that is screwed in place from inside the case. If you unscrew too far and keep turning, you can unscrew the cap from that internal screw.
 
D
Posts
886
Likes
470
Mr.Wolf Mr.Wolf
Ill hear around for some who could do it! Got two dealers around and will ask at a local forum. The watch is from 2010 so no warranty left unfortunately no warranty left. Thanks for your commitment!

Seeing as the watch dates back to 2010, it's probably due for a service anyway👍
 
BlackTalon
Posts
5,444
Likes
9,323
OP was definitely taking a chance deep sea diving with a watch that hasn't been serviced in 10 year. The helium escape valve would have been the least of my worries.
 
Mr.Wolf
Posts
65
Likes
6
I actually messed up a bit. I screwed it out fully and when I should screw it back it got a wrong angle on the threads and came on a bit tilted. When I tried to unscrew it again it fell off.

it’s been serviced three years ago, but I guess it’s time fore it again 👍
 
Mr.Wolf
Posts
65
Likes
6
The threads in the cap got damaged and couldn’t be screwed back. So I used the old one from last service.
 
Sign up or log in to reply...

Similar threads

Goseki

Should the Omega and helium crown both align horizontally or is it random?

Goseki Modern Omega Watches
hen
hen
Posts
10
Views
724
D

Which direction to turn the Helium crown

Dennerle Modern Omega Watches
ErichPryde
ErichPryde
Posts
11
Views
1K
watchstick_81

Helium valve came off....Seamaster 300m 2220.80

watchstick_81 Modern Omega Watches
watchstick_81
watchstick_81
Posts
30
Views
29K
O

Seamaster crown came off

omegafanaa Vintage Omega Watches Help, Discussion and Advice
O
omegafanaa
Posts
19
Views
11K
msp1518

Crown came off my Seamaster 300. Now what?

msp1518 Vintage Omega Watches Help, Discussion and Advice
Archer
Archer
Posts
17
Views
24K
TheCaptainOfTech

Crown for Omega Seamatser came off Help

TheCaptainOfTech Open Discussion
Archer
Archer
Posts
5
Views
4K