Omega CK2913 14755 165014 bezel insert

That insert looks awesome!
Will that insert fit a 165.014 1962 Seamaster? I'll roll the dice on any prototype you got!

Mcgyver - you are a true MacGyver! The definition of a "MacGyver Type" is “To assemble or repair something by ingenious improvisation, using everyday items that would not usually be used for the purpose” LOL…I think you’re there!

This thread was very motivating even though I don't have a watch with a bezel

Printing makes sense in the long run, as the sales will continue, but for a timeless one, if I had a watch, I'd go for etched or anodized, even just a bare etched metal is better than nothing 😀

This looks great and will be a great service to 2913, 14755, and 165.014 watches missing their inserts. They just don't look the same without it.

Did some more tests today-got the pad printing going really well with a new cliche!



Also tweaked the aluminum inserts dimensions - now it fits really well - it has been a good day!

I have been experimenting with how to glue and "bake" the inserts.
Many, many failed attempts resulted in - back to square one - use acetone based glues - as the naphtha based lacquers otherwise dissolves the glue during "baking".
Later I will try UV curing low viscosity epoxy as a faster method - the lacquer contains so much solvent it takes 3-4 coats with 4-8h drying time to get the finish right.

Here is a insert with two coats curing.

Looks great!

A step forward - first test version of a better pad printing setup is in place.






Testprint - paint with lume, three layers

Wow! What a great thread. @mcgyver you are doing a great job

Wow ! Great setup. I'd buy one . Don't even need one..... I just love solutions and not giving up..... Great work ! Kind regards. Achim

How does the thickness compare to an original one?

Aluminium version 0.13mm, printed version for ”baking” 0.05mm

A little update

Some of the "waste" produced.......

.......and finally some ok versions! (New cliché made with modified fonts)



Still waiting for UV cure Epoxi => done tests baking in naphta based lacquer...........not easy to get the results I'm looking for!

Wow, your into this! keep it going, it will pan out!!

After much trial and error I finally made an insert I'm pleased with.
I think I have redone the bezel twenty times or more and printed hundreds of inserts that are now placed on my wall of shame!
The best solution for ”baking” is a pad printed 70µm thick insert with lume covered with 7-10 layers of a special hard floor lacquer.
Sorry for poor quality pictures - looks better in real life!
The bezel is quite worn and the outer edge/rim from 12 to 18:00 in lower than 18-12:00 => more concave suface on this half!

Lots of work went into it! I am no expert but it looks awesome. Have you figure out what your going to charge for this service?

And very importantly - do you think somebody could order just the black part, without sending the metal part of the bezel. This would ease all the ordering process - if they are easy enough for any watchmaker to fit.

Well........yes, but it takes a bit of practice to get it in place nicely!
The aluminium version is "just"- glue in place (and coat if you would like to), and you're done.
This version requires more skill!
With a bezel that has less wear I think it is much easier, but I do not know as this is the only one I have access to!

It’s been said before on this thread, if we do not have to take our bezel off the watch and ship the bezel (overseas for some) it’s a bonus. So many things can go wrong! Its best to have something that can be shipped to us and we can install. As long as the final product looks like the original and just as good as the other bezel products out there it’s a no brainer. I like that it’s an insert also.
Do you need some testers, I am ready with my 165.014-62 Seamaster!
Cheers...