- Posts
- 313
- Likes
- 308
DonovanMartin
·I picked this up and noticed the bottom pusher seems a bit more stuck out. Does this look like it to you?
What would you do?
What would you do?
Speedmaster pusher concern
- Posts
- 23,127
- Likes
- 51,629
Dan S
·You should have it tightened by a watchmaker. The cap is coming unscrewed.
- Posts
- 29,111
- Likes
- 75,238
Archer
··Omega Qualified WatchmakerYep - movement needs to come out and then the screw can be tightened.
- Posts
- 313
- Likes
- 308
DonovanMartin
·Years ago I removed a movement from a Mark 2 that had a broken crystal and glass floating around. It made me a bit nervous but I was successful. I actually put it back into another Mark 2 case for the time being. I am entertaining the idea of doing this myself but first I'll ask a local watchmaker whom I sort of trust. I don't know him well enough to really know. But I don't want to loose this!
- Posts
- 23,127
- Likes
- 51,629
Dan S
·I’d say that this something you can do yourself if you have some tools and you’re comfortable pulling the movement. It’s a fairly simple repair and something I’ve done on a couple of occasions.
If you don’t want to do it, I’d recommend putting the watch into a ziplock. The cap doesn’t look like it’s about to fall off, but why take chances.
If you don’t want to do it, I’d recommend putting the watch into a ziplock. The cap doesn’t look like it’s about to fall off, but why take chances.
- Posts
- 313
- Likes
- 308
DonovanMartin
·I was doing some light reading on pusher replacement, etc..., and I thing this tool is needed: Bergeon 5901-P27 to tighten the pusher button. I don't really need it at this point I don't think. My question is, "why do people replace the pushers if they still have originals?"
I see people making comments like, "all original except the pushers" and it seems to hurt the value. Do they simply wear out? It seems they probably do over time but is there a gasket inside and the spring that can simply be replaced, keeping the original?
I see people making comments like, "all original except the pushers" and it seems to hurt the value. Do they simply wear out? It seems they probably do over time but is there a gasket inside and the spring that can simply be replaced, keeping the original?
- Posts
- 5,728
- Likes
- 27,003
YY77
·I was doing some light reading on pusher replacement, etc..., and I thing this tool is needed: Bergeon 5901-P27 to tighten the pusher button. I don't really need it at this point I don't think. My question is, "why do people replace the pushers if they still have originals?"
I see people making comments like, "all original except the pushers" and it seems to hurt the value. Do they simply wear out? It seems they probably do over time but is there a gasket inside and the spring that can simply be replaced, keeping the original?
Answer is in this post:
https://omegaforums.net/posts/2035216/
Archer ·
Just purchased a 69 Speedmaster 145.022 with original crown and pushers- no service marks inside case and all indicators and appearance consistent with entirely original specimen- even bezel can be dated as it is a "220" Error example dating to 1970 (with a few unfortunate paint chips). Like idea of maintaining original parts but my understanding is that pusher gaskets are difficult/impossible to replace, and crown gaskets not replaceable at all. Leaning towards replacing pushers and crown, but keeping originals for future reference/ potential resale. Make sense? Watchmakers...
- Posts
- 29,111
- Likes
- 75,238
Archer
··Omega Qualified WatchmakerI was doing some light reading on pusher replacement, etc..., and I thing this tool is needed: Bergeon 5901-P27 to tighten the pusher button.
- Posts
- 2,654
- Likes
- 5,351
SOG53
·If you want to wear it, best to just get it serviced and this will be fixed as well as likely other things that need attention.
- Posts
- 313
- Likes
- 308
DonovanMartin
·I ended up just doing it myself. Had sufficient tools and barely enough nerve. I will eventually be sending it in at some point for a service. I found some smudge marks on the inside of the middle case. Movement is beautiful. No marks before or after! The case gasket was ok but not super great.
