Community Stories

Removing a strap with a shoulderless spring bar from a no-holes case

john_coburg
Posts
215
Likes
303
Greetings all,
I've been an idiot and fastened a leather strap to a watch head without drilled lug holes using a spring bars without shoulders. The leather is really thick and rigid, so there isn't much wiggling around.
What are my options? Are there any clever tricks i'm missing, or is a hacksaw the best bet? And if so, why type is best for the job?
Thanking you in advance.
John
 
Spruce
Posts
7,573
Likes
60,744
Pliers? Twist, bend and pull?
 
marcn
Posts
1,046
Likes
5,432
Do you need to save the strap?

If not, with something comparable to a scalpel, carefully cut the strap along the axis of the spring bar. Replace those spring bars with ones with proper shoulders, and buy a new strap.
 
Evitzee
Posts
7,002
Likes
13,076
An X-Acto knife with a new #11 blade will allow you to slice the strap off. Better to sacrifice the strap than risking damage to the lugs or case.
 
john_coburg
Posts
215
Likes
303
Spruce Spruce
Pliers? Twist, bend and pull?
well i thought of that, but what are the chances of damage to the Speedmaster in question?
 
john_coburg
Posts
215
Likes
303
marcn marcn
Do you need to save the strap?

If not, with something comparable to a scalpel, carefully cut the strap along the axis of the spring bar. Replace those spring bars with ones with proper shoulders, and buy a new strap.
i do need to keep the strap. obviously the spring bars can go..
 
Evitzee
Posts
7,002
Likes
13,076
You can try dental floss....it sometimes works.
 
Dan S
Posts
21,456
Likes
48,720
You can keep trying with a sharp knife and other tools and hope you get lucky, but to my knowledge there is no reliable way to do it without cutting away the strap.
 
Spruce
Posts
7,573
Likes
60,744
john_coburg john_coburg
well i thought of that, but what are the chances of damage to the Speedmaster in question?
Regular spring bars are nowhere near as solid as a stainless steel case
 
eugeneandresson
Posts
5,044
Likes
15,510
Bernstein-3-0641-30123881-01.jpg
(making certain the sharp points dont touch the case)
 
marcn
Posts
1,046
Likes
5,432
There’s maybe merit to trying the flush cutting nipper like eugene showed (getting in between strap and lug by compressing the strap down and carefully cutting the spring bar) but personally—sacrifice the strap and move on.
 
Syzygy
Posts
1,200
Likes
3,883
It's tricky, and I was not successful in my attempt because the springbar had rusted/fused in to the lug hole....ultimately I ended up snipping the spring bar (wear safety glasses!), but a trusted collector suggested a razor blade to possibly slip in between the springbar and the lug. You may be able to work it and compress to get it free. I'd also suggest wearing gloves with rated cut protection in case you slip!
 
john_coburg
Posts
215
Likes
303
eugeneandresson eugeneandresson
Bernstein-3-0641-30123881-01.jpg
(making certain the sharp points dont touch the case)

I used a hacksaw to weaken the spring bar end, and then twisted out. Saved the lugs and the strap. Thank you all for the suggestions...this Bernstein solution would have saved me half an hour, but cost me fifteen quid.
 
Sign up or log in to reply...

Similar threads

john_coburg

removing a 'difficult' spring bar from a 20mm lug...

john_coburg Open Discussion
SkunkPrince
SkunkPrince
Posts
20
Views
7K