Seamaster 300m gmt questions

Posts
6
Likes
2
Greetings all,

I am new to this so please feel free to redirect me. I searched and could not find an exact fit.

I have a Seamaster 300m GMT ref. no. 2532.80. I bought it used, think it is circa 2007?

I love this piece and only have two things I would like to change. First the lume only lasts about an hour. I was advised by a reputable craftsman, experienced in reluming, that this particular piece is difficult to do because of the skeletonized hands and smallish hour markers. Two sources recommended that I send it back to Omega for a new dial and hands. Omega says I have to send in the watch for an estimate. I have no problem doing that, but, so they just have parts for a 2007 just lying around? I have no interest in turning my timpiece into a "Frankenwatch" as I don't particularly like the newer, larger hour indices. Does anyone have any experience with this or has actually had it done?

Next, the bracelet, is more comfortable than my older Submariner, but it has no microadjustments. This is problematic as my wrist swells throughout the day. This makes the watch way too loose in the morning and way too tight by end of day. Rubber straps are a little better but less visually appealing for my tastes. The adjustable clasps on the newer Omegas are great which prompted me to buy a new Seamaster bracelet, which fits, but not exactly (41mm vs 42m). Omegas says a newer adjustable clasp can be put on but I do not see how as the attachment points are different. Again, my question is whether or not anyone has any experience with this?

Feel free to tell me to just like it for what it is as I am totally fine with that. It would be nice if I could reasonably customize it a little, but not essential to my happiness. Thank you to all.

Dan

 
Posts
28
Likes
76
I have this watch, I absolutely love it.

I can’t help you with the lume, but I have added an omega adjustable clasp.

Your clasp options are:
  • 3-position clasp: 117STZ004666 --; shortest length @ 34.5mm
  • 6-position clasp: 117STZ001154 --; regular length @ 39.5mm
  • 6-position clasp with diver extension: 117STZ001159 --; longest length @ 44mm

I went for the 6 position 117STZ001154 as I’m not bothered about a divers extension and wanted the shorter clasp. You also need two new links to attach the clasp to the original bracelet, 4 new pins to fit the clasp and those links, and then 8 screws to put it all together. So I went with the following:

1 x 117STZ001154 clasp
2x 118st1515 links
8x screws (124ST3307)
4x 20mm pins (128ST0169)

I got all these parts either from eBay or swisswatchspares in the UK.

It’s not a cheap upgrade, but it transforms the watches wearability and I highly recommend you do it.

Good luck!
 
Posts
28
Likes
76
The picture shows what pins and links I ordered from swisswatchspares - I don’t know if he still stocks them though.

 
Posts
28
Likes
76
You’ll note I only bought one of the pinscrewset20 - this is because the link itself comes with a pin and two screws, so the pinscrewset20 makes up the remaining that you need.
 
Posts
1,586
Likes
3,153
I had my 2998.80 SMP chronograph relumed and there was no problem. Find another relumer.
 
Posts
28
Likes
76
@dfp if you send it back to omega they can fit new hands to it, no problem, they have stock of the original hands. My watch was serviced back in 2023 and it was fitted with new hands.
 
Posts
6
Likes
2
Trikster,

Extremely helpful, both facts and opinion.
Checked out the swisswatchspares site which looks great.
Did the new hands they put on glow any better than the ones they replaced?
I might send it in to Omega to see what they say about service, hands, relume. Have them do everything all at once. Costly, yes, but much cheaper probably than a new Blackbay 58 GMT (just bought one for my son as a gift for successfully defending his PhD, nice watch, but I like the Omega better). Will keep you posted.

Dan
 
Posts
6
Likes
2
I had my 2998.80 SMP chronograph relumed and there was no problem. Find another relumer.
Thanks for the feedback. Did you just have the hands relumed or the dial as well? Can I ask where you had it done? I am in New York, plenty of places up and down the US East Coast that all say they are great but hard to tell from a single photo. I had Kent Park at Everest Watchworks relume a watch for me several years ago and he did a great job but he is not answering emails, may have closed shop? Any and all help and opinions greatly appreciated, thank you.

Sincerely,
Dan
 
Posts
28
Likes
76
Trikster,

Extremely helpful, both facts and opinion.
Checked out the swisswatchspares site which looks great.
Did the new hands they put on glow any better than the ones they replaced?
I might send it in to Omega to see what they say about service, hands, relume. Have them do everything all at once. Costly, yes, but much cheaper probably than a new Blackbay 58 GMT (just bought one for my son as a gift for successfully defending his PhD, nice watch, but I like the Omega better). Will keep you posted.

Dan
I don’t recall the lume on the old hands being particularly poor; IIRC they just recommended the hands be changed along with a few other parts (like the crown m the winding stem) etc as part of a general service and overhaul. I got them to put a new bezel insert in too. The watch came back looking like more or less like new (no polish was necessary so I asked them not to refinish anything).
 
Posts
6
Likes
2
lume on my hands last an hour or two in the dark, not much use in low light.

Funny thing, I purchased a new bracelet for this a few years ago at the recommendation of a local Omega "boutique." It worked, but it was not what I expected as it extended too far past the ends of the lugs. Too late to return. It has an STZ00159 clasp on it. I may already have just about all I need, just need the time to take on a small project. Thanks again.
 
Posts
11
Likes
9
Greetings all,

I am new to this so please feel free to redirect me. I searched and could not find an exact fit.

I have a Seamaster 300m GMT ref. no. 2532.80. I bought it used, think it is circa 2007?

I love this piece and only have two things I would like to change. First the lume only lasts about an hour. I was advised by a reputable craftsman, experienced in reluming, that this particular piece is difficult to do because of the skeletonized hands and smallish hour markers. Two sources recommended that I send it back to Omega for a new dial and hands. Omega says I have to send in the watch for an estimate. I have no problem doing that, but, so they just have parts for a 2007 just lying around? I have no interest in turning my timpiece into a "Frankenwatch" as I don't particularly like the newer, larger hour indices. Does anyone have any experience with this or has actually had it done?

Next, the bracelet, is more comfortable than my older Submariner, but it has no microadjustments. This is problematic as my wrist swells throughout the day. This makes the watch way too loose in the morning and way too tight by end of day. Rubber straps are a little better but less visually appealing for my tastes. The adjustable clasps on the newer Omegas are great which prompted me to buy a new Seamaster bracelet, which fits, but not exactly (41mm vs 42m). Omegas says a newer adjustable clasp can be put on but I do not see how as the attachment points are different. Again, my question is whether or not anyone has any experience with this?

Feel free to tell me to just like it for what it is as I am totally fine with that. It would be nice if I could reasonably customize it a little, but not essential to my happiness. Thank you to all.

Dan

I have this same watch, but haven't worn it for a long time. I should probably consider selling off some of my collection at some point
 
Posts
10,824
Likes
16,844
Don't bother to change the hands and dial, you will be wasting over $500 for no benefit. Unless your watch has suffered water ingress, your lume will be performing virtually as well as it did when brand new, that is to say not very well. Superluminova doesn't deteriorate over time the way earlier radioactive lume did so you won't gain a fat lot by swapping parts.

The real issue is that Bond dial design just doesn't have big enough lume plots but the hands are even worse and become nearly impossible to read when in the dark for any extended period of time. The best solution but I appreciate a drastic one is to sell the watch and buy a Sword Hands GMT such as the Great White 2538.20 or the black dial 2534.50. Those shine like torches in comparison.

ps before buying anything at Swisswatchspares it is always advisable to first contact a boutique or dealer with the part numbers. Many bracelet parts are freely available for order and buying direct from the manufacturer will be noticeably cheaper than SWS who tends to be most useful on restricted or discontinued parts IME.
Edited:
 
Posts
1,445
Likes
1,471
Don't bother to change the hands and dial, you will be wasting over $500 for no benefit. Unless your watch has suffered water ingress, your lume will be performing virtually as well as it did when brand new, that is to say not very well. Superluminova doesn't deteriorate over time the way earlier radioactive lume did so you won't gain a fat lot by swapping parts. The real issue is that Bond dial design just doesn't have big enough lume plots but the hands are even worse and become nearly impossible to read when in the dark for any extended period of time. The best solution but I appreciate a drastic one is to sell the watch and buy a Sword Hands GMT such as the Great White 2538.20 or the black dial 2534. Those shine like torches in comparison.

ps before buying anything at Swisswatchspares it is always advisable to first contact a boutique or dealer with the part numbers. Many bracelet parts are freely available for order and buying direct from the manufacturer will be noticeably cheaper than SWS who tends to be most useful on restricted or discontinued parts IME.
I agree with everything padders said.

With respect to parts, Omega still has in stock most parts for watches made in the last 30 years. If you are looking for links, clasps, bracelets, etc. always start with Omega and buy from third parties (like SWS) as a last resort. Any OB or AD can order parts for you. Or if you have an Omega certified independent watchmaker in your area they can order. Or you can call the Swatch Group telephone number for your country or area and they should be able to connect you with the department that handles spare parts.

Internal watch parts (like dials, hands, etc.) normally require a full service to obtain replacements.
 
Posts
1,586
Likes
3,153
Thanks for the feedback. Did you just have the hands relumed or the dial as well? Can I ask where you had it done? I am in New York, plenty of places up and down the US East Coast that all say they are great but hard to tell from a single photo. I had Kent Park at Everest Watchworks relume a watch for me several years ago and he did a great job but he is not answering emails, may have closed shop? Any and all help and opinions greatly appreciated, thank you.

Sincerely,
Dan

Hours, minutes, and seconds hands, and dial. MCWW - in 2014, though. Kent did three watches for me earlier this year.
 
Posts
10,824
Likes
16,844
Hours, minutes, and seconds hands, and dial. MCWW - in 2014, though. Kent did three watches for me earlier this year.
Was yours originally tritium lume that had lost potency perchance? There a relume or new dial does make sense.
 
Posts
12
Likes
5
I’d be careful about changing too much on this one. Part of the appeal of an older Seamaster is keeping it true to its original design. I’d definitely get an assessment from Omega before considering a new dial and hands, and specifically ask whether they can source the original-spec parts rather than newer replacements.

The clasp issue is trickier. I’d be surprised if the newer micro-adjust clasp were a straightforward fit given the different attachment points. Perhaps an Omega specialist could suggest a compatible alternative. Either way, I’d exhaust those options before modifying anything permanently. It’s a lovely watch as it is!
 
Posts
1,586
Likes
3,153
Was yours originally tritium lume that had lost potency perchance? There a relume or new dial does make sense.

Hands didn't match the dial. It was early 90s - 1993 or 94 - and the hands were replaced later, before I bought it.
 
Posts
6
Likes
2
Thanks to all. Not really interested in switching out the dial and hands as I fear it will change the original appearance too much. I thought of selling it, but after wearing it for a few days I remembered why I really like it. Currently waiting for a rubber strap I ordered as well as the clasp links. Love to tinker, nothing to lose, keeps me out of trouble (unless it leads me to buying a new watch).
 
Posts
6
Likes
2
Just got in my Monstrap FKM rubber/nylon hybrid strap. Very nice, looks good, fits well, curved end. One comment on wearability and setting lengths with the deployment clasp. I tried to do it the right way first by aligning the hole in the strap with the pin on the clasp. It was too loose so I tried to readjust but had trouble getting the strap off of the pin, there was a lot of resistant and no real leeway to just pull the strap off of the pin. Went to next hole, this one was too tight, same trouble getting it off the pin due to resistance, etc. Brainstorm, the amount of resistance was enough to keep the strap in place without setting the pin in one of the holes. Et Voila`, c'est ça!! The added benefit now is that I can adjust much more easily by just sliding the strap between holes. And, it is secure in the clasp, only moves with a strong tug. All well and good until it falls off. Fingers crossed.

P.S. the clasp links for fitting the new clasp to my old bracelet come on Monday. More tinkering to come.